What a day! I only got a few runs in and I spent most of the day chasing wind, a fool’s errand as it turned out, but not for lack of wind. I took a few wobbly runs at the cut while there were 2 other guys there. It was gusting over 50. I felt pretty over-powered on my 3.5 with extra downhaul. The cut was fantastic in a SE. Too bad I was so overpowered. We were well down wind of the breakers on the outside. There was a wave that was peaking right in the middle of the run that was manageable and fun. One run could take you all the way to the tip of North beach, although I turned in the middle where the little wave was. The current was coming in and the wind was blowing in, same direction, but I had enough power to stay upwind as long as I didn’t spend too much time in the water- fast waterstarts. There was a rock wall with waves directly downwind. The sand blowing down the beach really stung! The next day there was a photo of one of the guys, Jerry Evens, doing a loop at the cut, on page 2 of the Boston Globe. I saw him do a loop in front of a camera man while I was rigging. I leave voluntarily- When they quit, I packed up and headed off to West Dennis. I didn’t want to sail by myself, overpowered, with the chop, waves and current at the cut. Interviewed & kicked out of W. Dennis- There was no one sailing at West Dennis so I rigged to sail on the inside. I had never seen the water so high there! I was just about to step on my board when the environmental police showed up to say that they were closing the beach because water was starting to wash across it and into the road and it was still 1 ½ hours before high tide. The part of the beach that I was on was might be cut off. As I was packing up, channel 4 news arrived and asked if they could interview me. (Apparently, they played a clip of it on the 11:00 p.m. news and the 5:00 a.m. news, I also found it online.) On the way out, I turned in at the Lighthouse Inn parking lot to see if the waves were getting close to the hotel. Some water was starting to wash across the beach just to the right of the hotel, where we rig sometimes, and into their lot. I hope the Hotel didn’t get much water damage. Kicked out of Duxbury- I decided to stop off at Duxbury on the way home for a brief session before dark. I was rigging there, almost done, when the harbor master drove up and asked me to leave because I didn’t have a sailing buddy. Damn!!! It looked like it would have been great. The waves were rolling in on the lower parking lot, up above the signs. I tried explaining that I had left an open ocean site, because I didn't have a sailing buddy, to come here where it was enclosed and safe. He didn't betray even the slightest hint of sympathy.
First Board- 152 x 44, Plywood, "Close to the Edge" 1/2" Baltic birch, planed down on edges & tips (on top only), to reduce weight, increase flex, and create thinner rails. I used a hand held power plane to rough it out, then small belt sander to make smooth. Covered the top with putty to fill grain and voids and sanded with random orbit sander. NOTE- next time sand more to thin rails to 1/8" or 3/16" all around for better grip in the water, less weight and added flex.
Cost of wood- $25, (half of a 60" x60" sheet). I taped off the edge and sprayed several coats of flat waterborne paint on top, left bottom unpainted, applied graphics, brushed on 1 coat of epoxy on top and 2 on bottom. NOTE- next time seal bottom with clear spray on finish and topcoat with 1 coat of epoxy to save weight, (1 coat of epoxy over bare wood isn't smooth enough).
Inserts for handle & footstraps- brass, from McMaster & Carr.
Holes for fins drilled big, filled with epoxy, redrilled.
. I tried smaller home made ones but they were slipping out. These work much better.
Handle- mahogany, pattern drawn on with magic marker, cut on band saw, sanded on stationary belt sander.
Pads, stick-on, $20 for pair. Straps- Dakine windsurfing straps from an old board.
Graphics- "Close to the Edge", digital file from Internet printed on water slide decal paper. Rolling Stones mouth- sticker. I tried rice paper made for surfboard graphics, looks good but it requires about 3 coats of epoxy to cover it. Note- next time, for clear decal, use clear matt label paper, put a layer of sealer or epoxy down under the decal.
Epoxy- 8 ounces per coat, clear boatbuilding epoxy, $10.
Update- How did it ride? It was O.K. in flat water/ light winds. It really went upwind well! Problems- no flex, heavy, no rocker, wide tips. Symptoms- I had to use a lot of back foot pressure to keep the tip up in any chop at all since it had 0 rocker and wide tips. I got a lot of thigh burn using this board, same muscles as skiing. It splashed in my face a lot. Retired after about 1 year.
Second Board- 132 x 41.5, Plywood, "Storm Chaser" 2 layers of 1/4" birch plywood glued up with 1/2" of rocker on each end, planed down on edges and tips (on top only). Cost of wood-$0, I used scrap from the shop.
This board was lighter than my first and had some flex but otherwise had many of the same problems as my first board, not enough rocker, tiring on legs, spray in the face. Retired after 1 year.
Mad Cow- 180 x 60, Pink foam, fiberglass, plywood bottom, twin tip surfboard.
This is the ultimate light wind cruiser. It works down to 10 MPH with 17 meter Zephyre, or 8 MPH with Flysurfer 15 meter Speed 2. Very light weight board but extremely delicate, not enough layers of fiberglass cloth on top (1 full layer with second layer under footpads and handle). Plenty of rocker. Fun sometimes. Pink insulation foam is cheap but outgasses when it heats up. This causes delamination bubbles on the board if left face up in sun on beach. Still in use until it breaks.
Plywood skimboard
This board has rocker and concave. I'm still experimenting with it, want to try it with small fins for better upwind grip. It has almost no flotation, which makes waterstarts hard. I think that's why most kite skimboards are made out of foam.
Link for Wooden Surfboard, made from scrap, with hollow chambers-
May 21, 2011 Scoopers Home for Wayward and Delaminated Boards- I took Jean's broken foam core Mako into the shop to give it some TLC and to save it from the trash can. I know this old board has some stories to tell. I'm hoping it will whisper them to me the next time I take it out in some wind. Here's how I tried to bring it back to health- Click on pics to see large.
Prep- I cut the ragged edge of the old foam to make a clean edge, and removed a few small pieces of foam that were left around the fin holes. I sanded the fur left from the foam on the top and bottom sheet but it was coming off slowly so I mostly left it.
Making Parts, Edging- I glued up Versatex PVC board to make a blank for the new edgeing. Traced the shape from the board and cut it out, sanded it by eye to get the taper on the edgeing.
Foam- I used Last-A-Foam, from Fiberglass Supply, to make a new foam core section. I traced the PVC edge onto the Foam, cut it out, sanded the foam to the thickness and concave by eye. Used a knife to cut out the hole for the old fin hole reinforcement block, (which looked like solid thickened epoxy).
Glue Up- I glued the whole mess together, old top and bottom sheet, new foam, new PVC edging, old fin hole block, with lots of West epoxy. It was more floppy than I expected so I put small clamping blocks on the place where new edge meets old edge to get rid of sag there while it dried.
Fiberglass Reinforcment- I have low confidence in the strength of the repair. After all, the original construction wasn't strong enough and the repaired board will always be less strong than the original. So I sanded the bottom, put 1 layer of cloth over the bottom of the board, 3 coats of epoxy. I tried to wrap the cloth around the edges but it didn't work, should have used thinner cloth. You can see the texture of the cloth if you click on the picture to see large.
The Result? It looks almost as good as new, feels a little heavier. I know it will work but not sure for how long. One session? Stay tuned.
11/30/14 Follow up- The board is probably a little heavier and stiffer than the original but has worked great as my main board in waves and chop for almost 4 years. The other end just started to delaminate. I reglued it and it's back in the rotation.
Mitch's Weekly Report covers the windsurfing, surfing, kiting, and SUP scene in the Pt. Judith, R.I. area and neighboring vicinity. It's brief and concise, with a weekly picture, water temps, wave heights, the best action of the week, and any other important stuff that's on Mitch's mind.
To sign up to receive Mitch's Weekly Report send an email to mitchlev10@cox.net with "Sign me up" in the subject line.
Interviewed & kicked out of W. Dennis- There was no one sailing at West Dennis so I rigged to sail on the inside. I had never seen the water so high there! I was just about to step on my board when the environmental police showed up to say that they were closing the beach because water was starting to wash across it and into the road and it was still 1 ½ hours before high tide. The part of the beach that I was on was might be cut off. As I was packing up, channel 4 news arrived and asked if they could interview me. (Apparently, they played a clip of it on the 11:00 p.m. news and the 5:00 a.m. news, I also found it online.) On the way out, I turned in at the Lighthouse Inn parking lot to see if the waves were getting close to the hotel. Some water was starting to wash across the beach just to the right of the hotel, where we rig sometimes, and into their lot. I hope the Hotel didn’t get much water damage. Kicked out of Duxbury- I decided to stop off at Duxbury on the way home for a brief session before dark. I was rigging there, almost done, when the harbor master drove up and asked me to leave because I didn’t have a sailing buddy. Damn!!! It looked like it would have been great. The waves were rolling in on the lower parking lot, up above the signs. I tried explaining that I had left an open ocean site, because I didn't have a sailing buddy, to come here where it was enclosed and safe. He didn't betray even the slightest hint of sympathy.
Posts
web225H.jpg)
